New DH55 Series Offset Disks
REQUEST A QUOTE
Key Features
- Adjustable disk blade scrapers
- Oil bath tapered roller bearings minimize maintenance
- Working widths from 10-ft. to 13.75-ft.
Features
Adjustable disk blade scrapers increase productivity
Adjustable disk blade scrapers keep disk blades clean and performing in wet and sticky soils for increased productivity.
Scrapers clean disk blades
Scrapers work great in wet and sticky soils
End washers and wrenches keep gang shaft end nut tight
End washers help keep the gang shaft end nut tightened during operation, increasing gang wear life.
Two gang nut wrenches are supplied with each unit and securely attached to the unit, ready to use when the gangs need tightening.
Keeping gangs tightened increases wear life
Gang nut wrenches are always there when needed
Transport locks secure disk wings
Transport locks are standard, ensuring disk wings are in secure transport mode.
Transport locks secure disk wings cylinder
Two separate control arms create consistent performance
Two separate control arms are standard, one for transport leveling and one for leveling while the disk is in the ground. Once set for a given soil condition, the disk will continue to perform with consistency.
Control arms level in ground and during transport
Easy to set for desired soil condition
Oil bath tapered roller bearings minimize maintenance
Oil bath tapered roller bearings, sealed with industrial-grade seals, keep maintenance to a minimum and profitable working hours at a maximum. The bearings come complete with a wear plate.
Minimal maintenance increases work hours
Sealed with industrial-grade seals
Specifications
Transport
| Width | 3.7 m 12 ft |
|---|---|
| Ground clearance with base blades | |
| Wheel hub bearings | Dual tapered roller bearings |
| Height | |
| Length |
Working
| Approximate working width | 3.4 m 11 ft |
|---|---|
| Maximum penetration |
Weight
| Net | 5443.1 kg 12000 lb |
|---|---|
| Weight per disk blade | 272.2 kg 600 lb |
Tractor requirements
| Recommended PTO hp range | |
|---|---|
| Recommended drawbar hp range | 167.8 kW 225+ hp |
Frame
| Type | Single offset rigid |
|---|---|
| Duty | Heavy |
| Tube size | 20.3x20.3x1.3 cm 8x8x0.5 in. |
Hitch
| Front hitch type | Pintle |
|---|---|
| Bolt-on rear hitch |
Disk blades
| Spacing | 35.6 cm 14 in. |
|---|---|
| Quantity | 20 |
| Type | Notched (front) Notched (rear) Standard |
| Blade concavity |
Available blade sizes
| Blade option one | 813x12.7 mm 32x0.5 in. |
|---|---|
| Blade option two | |
| Blade option three | |
| Blade option four | |
| Blade option five | |
| Blade option six |
Disk gangs
| Front angle | 3 positions |
|---|---|
| Rear angle | 3 positions |
| Furrow fillers | |
| Axle size | 6.4 cm 2.5 in. |
| Axle material | Round heat treated alloy steel threaded on both ends |
| Bearing type | Oil bath tapered roller |
| Bearing wear plates | Standard |
| Bearing standards | Welded, Reinforced |
| Scrapers | Adjustable |
Lighting and safety
| Markings | SMV |
|---|---|
| Safety tow chain | Yes |
| Lights | Yes |
Tires
| Type | 2 - Radial industrial |
|---|---|
| Size | 385/65R22.5 |
| Wheel hub type | 5-Spoke dayton hubs |
Set-up time
| Labor hours | 2-3 for two people |
|---|
Warranty
| Time period | 1 year |
|---|